| Author |
|
Handy121
Newbie
Joined: Apr 16 2011
Online Status: Offline
Posts: 38
Member's Gallery:
View Gallery
Location:
U.S. - California
|
| Posted: Jun 09 2011 at 6:55pm | IP Logged
|
|
|
I recently posted a problem with my frontier trans leak and had found out the bolts were missing to the flex plate and that broke off the pilot bushing of the torque Converter causing the leak. I have replaced the Converter and it runs fine except at a stop light or when sitting in traffic the idle is down to 400 or 500 and I have to step on the gas to get it to 750. Anyone know the best way to fix this problem?
__________________
2001 Nissan Frontier 4x4 Super Charged V6 145,000 miles
|
| Back to Top |
|
| |
frontierguy
Senior Member
Master Mechanic
Joined: May 20 2008
Online Status: Offline
Posts: 2591
Member's Gallery:
View Gallery
Location:
U.S. - Pennsylvania
|
| Posted: Jun 09 2011 at 7:48pm | IP Logged
|
|
|
Warm eng to operating temp-rev at 2000 RPM for 2 minutes-
shut off engine-dis connect TPS connector(lower one)-start
eng-rev several times- adj idle speed screw to obtain 700 +
or - 50 RPM- shut off eng-reconnect TPS. The idle speed
screw is on the back of the air chamber-DO NOT ADJUST the
throttle stop screw at the throttle blade!!!!!
__________________
'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.
Nissan Technician 25 + years
2011 John Deere X720SE
|
| Back to Top |
|
| |
Handy121
Newbie
Joined: Apr 16 2011
Online Status: Offline
Posts: 38
Member's Gallery:
View Gallery
Location:
U.S. - California
|
| Posted: Jun 09 2011 at 8:42pm | IP Logged
|
|
|
Is that the Transmission Position Sensor I dis connect? What is TPS and where is it? Please help with the location of the Air Chamber, on the throtle body? Will that fix the idle in Drive. The idle speed is 750 in park and neutral no problems there!
Thank You so much for the input. When is your birthday? Send me your e-mail and I'll send you a card. I was born in Easton, PA. Can you suggest KYB or Bilstein or Monroe Prof front shock by part number? My front shocks are gone. Can I lower the front end by an inch by backing off the torsion bar bolt? Thanks so much  My e-mail is at www.althingsfromhim.com
__________________
2001 Nissan Frontier 4x4 Super Charged V6 145,000 miles
|
| Back to Top |
|
| |
frontierguy
Senior Member
Master Mechanic
Joined: May 20 2008
Online Status: Offline
Posts: 2591
Member's Gallery:
View Gallery
Location:
U.S. - Pennsylvania
|
| Posted: Jun 11 2011 at 5:04pm | IP Logged
|
|
|
I think it best to get a professional technician to correct
your concern.Bilstein. If you lower the ride height, it
will screw up the front end geometry, will need to properly
align the front suspension.
__________________
'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.
Nissan Technician 25 + years
2011 John Deere X720SE
|
| Back to Top |
|
| |
Active Topics 
Memberlist 
Search 
Help 
Register 
Login
Nissan Frontier Forums : General
Topic: 2001 Frontier 4x4 sc low idle in drive
